Cubox-i bullseye -> bookworm Upgrade failure

Hi,

I'd check if /etc/network/interfaces has end0 or something else (like
eth0). Probably the network interface got renamed as part of the upgrade.

Post by Rainer Dorsch
Linux test-machine 6.1.0-10-armmp #1 SMP Debian 6.1.38-2 (2023-07-27) armv7l
GNU/Linux
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group
default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host noprefixroute
valid_lft forever preferred_lft forever
2: end0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default
qlen 1000
link/ether d0:63:b4:00:2b:ac brd ff:ff:ff:ff:ff:ff
ifup: unknown interface end0

[SNIP]

Post by Rainer Dorsch
Many thanks
Rainer

Rainer Dorsch

2023-08-07 07:40:01 UTC

Post by RobJE Debian ARM
Hi,

I'd check if /etc/network/interfaces has end0 or something else (like
eth0). Probably the network interface got renamed as part of the upgrade.

Good that my devices have a serial console. But I remember that there are also
cubox-i devices out there without. Thus if they try to update, they will fail
and have to reinstall.

Should Reco's comment

Try adding "net.ifnames=0" to kernel's commandline.

go into the release notes for armhf?

Thanks
Rainer

--
Rainer Dorsch
http://bokomoko.de/

Reco

2023-08-04 08:30:01 UTC

Hi.

Post by Rainer Dorsch
[ 7.771809] fec 2188000.ethernet eth0: registered PHC device 0
[ 7.942031] fec 2188000.ethernet end0: renamed from eth0

Enjoy your (un)Predictable Interface Names.
Try adding "net.ifnames=0" to kernel's commandline.

Reco

Steve Langasek

2023-08-13 22:10:11 UTC

Post by Rainer Dorsch
[ 7.771809] fec 2188000.ethernet eth0: registered PHC device 0
[ 7.942031] fec 2188000.ethernet end0: renamed from eth0

Enjoy your (un)Predictable Interface Names.
Try adding "net.ifnames=0" to kernel's commandline.

They're perfectly predictable, they're just not backwards-compatible.

Forcing systems to use the legacy naming scheme to avoid the transition is
short-sighted.

--
Steve Langasek Give me a lever long enough and a Free OS
Debian Developer to set it on, and I can move the world.
Ubuntu Developer https://www.debian.org/
***@ubuntu.com ***@debian.org

Reco

2023-08-14 05:10:01 UTC

Hi.

Post by Rainer Dorsch
[ 7.771809] fec 2188000.ethernet eth0: registered PHC device 0
[ 7.942031] fec 2188000.ethernet end0: renamed from eth0

Enjoy your (un)Predictable Interface Names.
Try adding "net.ifnames=0" to kernel's commandline.

They're perfectly predictable, they're just not backwards-compatible.

If one cannot predict the interface name after the reboot then obviously
Predictable Interface Names are not that predictable :)
I'm well aware of the limitations of systemd's "interface naming
scheme", and breaking user's setup on udev upgrade is only one of them.

Post by Steve Langasek
Forcing systems to use the legacy naming scheme to avoid the transition is
short-sighted.

So is breaking user's setup.

How about alerting end-user that "did you know your interface name
will change after the reboot thus possibly breaking your network
configuration?". I heard there are certain Release Notes that were used
to say things like that in the past ;)

Or, how about adding debconf question to udev that will ask the user
"would you like to keep your current interface(s) name(s)"?

Or, since the kernel is actually capable of using alternative nic names,
how about teaching ifupdown using those?

Reco

Steve Langasek

2023-08-15 19:40:01 UTC

Post by Rainer Dorsch
[ 7.771809] fec 2188000.ethernet eth0: registered PHC device 0
[ 7.942031] fec 2188000.ethernet end0: renamed from eth0

Enjoy your (un)Predictable Interface Names.
Try adding "net.ifnames=0" to kernel's commandline.

They're perfectly predictable, they're just not backwards-compatible.

If one cannot predict the interface name after the reboot then obviously
Predictable Interface Names are not that predictable :)

Can one not? That seems like something that should be addressed in
general, then.

Post by Steve Langasek
Forcing systems to use the legacy naming scheme to avoid the transition is
short-sighted.

So is breaking user's setup.

Yes, but *having done so*, trying to roll back the new default behavior
instead of leaning into it is just going to cause more problems down the
line.

You have to make changes to config files in response to this change, so it
might as well be /etc/network/interfaces instead of your bootloader config.

Post by Reco
How about alerting end-user that "did you know your interface name
will change after the reboot thus possibly breaking your network
configuration?". I heard there are certain Release Notes that were used
to say things like that in the past ;)

I think that's a very good idea. https://bugs.debian.org/release-notes ?

--
Steve Langasek Give me a lever long enough and a Free OS
Debian Developer to set it on, and I can move the world.
Ubuntu Developer https://www.debian.org/
***@ubuntu.com ***@debian.org

Rainer Dorsch

2023-08-29 12:40:01 UTC

I think that's a very good idea. https://bugs.debian.org/release-notes ?

That would be an improvement over the current status. Should I open a bug
report?

Though if there would a meaningful (=not many false positives and false
negatives) message during the upgrade, that would be much better. Users tend
not to read release notes...

Also I think the issue goes much beyond ifupdown, e.g. shorewall uses network
interface names in its config files as well.

Thanks
Rainer

--
Rainer Dorsch
http://bokomoko.de/

Steve Langasek

2023-08-29 15:30:02 UTC

Post by Rainer Dorsch

I think that's a very good idea. https://bugs.debian.org/release-notes ?

That would be an improvement over the current status. Should I open a bug
report?

I would encourage this, yes.

--
Steve Langasek Give me a lever long enough and a Free OS
Debian Developer to set it on, and I can move the world.
Ubuntu Developer https://www.debian.org/
***@ubuntu.com ***@debian.org

Rainer Dorsch

2023-08-30 07:40:01 UTC

Post by Rainer Dorsch

I think that's a very good idea. https://bugs.debian.org/release-notes ?

That would be an improvement over the current status. Should I open a bug
report?

I would encourage this, yes.

https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=1050833

Justin followed up with a question:

Are you saying that armhf machines still used one of the old interface
naming schemes (https://wiki.debian.org/NetworkInterfaceNames) on
bullseye, and hadn't yet switched over to "predictable" names?

That is what I observed after installing bullseye and upgrading to bookworm.
If anybody has insight why armhf did that later, please share there. Also any
other follow-up discussion probably should happen in the bugreport.

Many thanks
Rainer

--
Rainer Dorsch
http://bokomoko.de/

Paul Wise

2023-08-16 03:20:01 UTC

Post by Reco
Enjoy your (un)Predictable Interface Names.
Try adding "net.ifnames=0" to kernel's commandline.

Personally, I would switch away from hardcoding interface names.
ifupdown can do interface name wildcards and mac matching.

The other solutions for this problem (systemd-networkd, NetworkManager,
ifupdown-ng, probably ifupdown2) are much more flexible though.

--
bye,
pabs

https://wiki.debian.org/PaulWise

Rainer Dorsch

2023-08-04 10:40:02 UTC

Hi,

I found the root cause of the issue myself:

In /etc/network/interfaces I had to replace eth0 with end0:

# The primary network interface
allow-hotplug eth0
iface eth0 inet dhcp
# This is an autoconfigured IPv6 interface
iface eth0 inet6 auto

I hope that helps somebody to debug his network issues.

Rainer

Post by Rainer Dorsch
Hi,
I did a test installation with a bullseye installer on a cubox-i and then
upgraded to bookworm. After the upgrade the network was gone. Even booting
with the previous kernel 5.10.0-23-armmp does not bring the network back.
Any hints and ideas are welcome.
Linux test-machine 6.1.0-10-armmp #1 SMP Debian 6.1.38-2 (2023-07-27) armv7l
GNU/Linux
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group
default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host noprefixroute
valid_lft forever preferred_lft forever
2: end0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default
qlen 1000
link/ether d0:63:b4:00:2b:ac brd ff:ff:ff:ff:ff:ff
ifup: unknown interface end0
[ 7.771809] fec 2188000.ethernet eth0: registered PHC device 0
[ 7.942031] fec 2188000.ethernet end0: renamed from eth0
[ 0.000000] Booting Linux on physical CPU 0x0
(gcc-12 (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40)
#1 SMP Debian 6.1.38-2 (2023-07-27)
[ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7),
cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing
instruction cache
[ 0.000000] OF: fdt: Machine model: SolidRun Cubox-i Dual/Quad
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] efi: UEFI not found.
[ 0.000000] cma: Reserved 16 MiB at 0x4f000000
[ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff]
[ 0.000000] Normal empty
[ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff]
[ 0.000000] Initmem setup node 0 [mem
0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 18
pages/cpu s41620 r8192 d23916 u73728 [ 0.000000] pcpu-alloc: s41620
r8192 d23916 u73728 alloc=18*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260416
[ 0.000000] Kernel command line: console=ttymxc0,115200 quiet [
0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes,
linear)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144
bytes, linear)
[ 0.000000] mem auto-init: stack:all(zero), heap alloc:on, heap free:off
[ 0.000000] Memory: 979508K/1048576K available (11264K kernel code, 1693K
rwdata, 3568K rodata, 2048K init, 378K bss, 52684K reserved, 16384K cma-
reserved, 245760K highmem)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] ftrace: allocating 39313 entries in 116 pages
[ 0.000000] ftrace: allocated 116 pages with 4 groups
[ 0.000000] trace event string verifier disabled
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2.
[ 0.000000] Rude variant of Tasks RCU enabled.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25
jiffies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] L2C-310 errata 752271 769419 enabled
[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9
[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9
[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines
[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled
[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB
[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001
[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on
contention. [ 0.000000] Switching to timer-based delay loop, resolution
333ns [ 0.000001] sched_clock: 32 bits at 3000kHz, resolution 333ns,
wraps every 715827882841ns
0xffffffff, max_idle_ns: 637086815595 ns
[ 0.002978] Console: colour dummy device 80x30
[ 0.003035] Calibrating delay loop (skipped), value calculated using
timer frequency.. 6.00 BogoMIPS (lpj=12000)
[ 0.003050] pid_max: default: 32768 minimum: 301
[ 0.003724] LSM: Security Framework initializing
[ 0.003855] landlock: Up and running.
[ 0.003860] Yama: disabled by default; enable with sysctl kernel.yama.*
[ 0.004189] AppArmor: AppArmor initialized
[ 0.004203] TOMOYO Linux initialized
[ 0.004244] LSM support for eBPF active
[ 0.004571] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes,
linear)
[ 0.004596] Mountpoint-cache hash table entries: 2048 (order: 1, 8192
bytes, linear)
[ 0.006410] CPU: Testing write buffer coherency: ok
[ 0.006491] CPU0: Spectre v2: using BPIALL workaround
[ 0.007083] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.008408] cblist_init_generic: Setting adjustable number of callback
queues.
[ 0.008418] cblist_init_generic: Setting shift to 1 and lim to 1.
[ 0.008588] cblist_init_generic: Setting shift to 1 and lim to 1.
[ 0.008901] Setting up static identity map for 0x10300000 - 0x103000ac
[ 0.010363] rcu: Hierarchical SRCU implementation.
[ 0.010369] rcu: Max phase no-delay instances is 1000.
[ 0.013190] EFI services will not be available.
[ 0.013764] smp: Bringing up secondary CPUs ...
[ 0.015078] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.015097] CPU1: Spectre v2: using BPIALL workaround
[ 0.015280] smp: Brought up 1 node, 2 CPUs
[ 0.015292] SMP: Total of 2 processors activated (12.00 BogoMIPS).
[ 0.015303] CPU: All CPU(s) started in SVC mode.
[ 0.016370] devtmpfs: initialized
[ 0.027202] VFP support v0.3: implementor 41 architecture 3 part 30
variant 9 rev 4
0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.027745] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[ 0.028987] pinctrl core: initialized pinctrl subsystem
[ 0.029986] DMI not present or invalid.
[ 0.030952] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.058857] DMA: preallocated 256 KiB pool for atomic coherent
allocations [ 0.060093] audit: initializing netlink subsys (disabled)
[ 0.060583] audit: type=2000 audit(0.060:1): state=initialized
audit_enabled=0 res=1
[ 0.062220] thermal_sys: Registered thermal governor 'fair_share'
[ 0.062230] thermal_sys: Registered thermal governor 'bang_bang'
[ 0.062237] thermal_sys: Registered thermal governor 'step_wise'
[ 0.062242] thermal_sys: Registered thermal governor 'user_space'
[ 0.062246] thermal_sys: Registered thermal governor 'power_allocator'
[ 0.062404] CPU identified as i.MX6Q, silicon rev 1.2
[ 0.070873] platform 120000.hdmi: Fixed dependency cycle(s) with /soc/
[ 0.070898] platform 120000.hdmi: Fixed dependency cycle(s) with /soc/
[ 0.079574] platform 20e0000.iomuxc-gpr:ipu1_csi0_mux: Fixed dependency
[ 0.079778] platform 20e0000.iomuxc-gpr:ipu2_csi1_mux: Fixed dependency
[ 0.093599] No ATAGs?
[ 0.093736] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1
watchpoint registers.
[ 0.093748] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.095779] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver
[ 0.098072] Serial: AMBA PL011 UART driver
[ 0.105846] kprobes: kprobe jump-optimization is enabled. All kprobes are
optimized if possible.
[ 0.115775] iommu: Default domain type: Translated
[ 0.115788] iommu: DMA domain TLB invalidation policy: strict mode
[ 0.119241] NetLabel: Initializing
[ 0.119249] NetLabel: domain hash size = 128
[ 0.119256] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO
[ 0.119341] NetLabel: unlabeled traffic allowed by default
[ 0.119626] vgaarb: loaded
[ 0.131890] clocksource: Switched to clocksource mxc_timer1
[ 0.225695] VFS: Disk quotas dquot_6.6.0
[ 0.225879] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096
bytes) [ 0.226868] AppArmor: AppArmor Filesystem Enabled
[ 0.240775] NET: Registered PF_INET protocol family
[ 0.241330] IP idents hash table entries: 16384 (order: 5, 131072 bytes,
linear)
[ 0.244460] tcp_listen_portaddr_hash hash table entries: 512 (order: 0,
4096 bytes, linear)
[ 0.245084] Table-perturb hash table entries: 65536 (order: 6, 262144
bytes, linear)
[ 0.245192] TCP established hash table entries: 8192 (order: 3, 32768
bytes, linear)
[ 0.245591] TCP bind hash table entries: 8192 (order: 5, 131072 bytes,
linear)
[ 0.245829] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.246445] MPTCP token hash table entries: 1024 (order: 2, 16384 bytes,
linear)
[ 0.246594] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.246673] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes,
linear)
[ 0.246981] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.247038] NET: Registered PF_XDP protocol family
[ 0.247055] PCI: CLS 0 bytes, default 64
[ 0.247749] armv7-pmu pmu: hw perfevents: no interrupt-affinity property,
guessing.
[ 0.248128] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7
counters available
[ 0.248228] Trying to unpack rootfs image as initramfs...
[ 0.251414] Initialise system trusted keyrings
[ 0.251603] Key type blacklist registered
[ 0.252364] workingset: timestamp_bits=14 max_order=18 bucket_order=4
[ 0.263271] zbud: loaded
[ 0.271628] integrity: Platform Keyring initialized
[ 0.271696] integrity: Machine keyring initialized
[ 0.271708] Key type asymmetric registered
[ 0.271718] Asymmetric key parser 'x509' registered
[ 3.267956] Freeing initrd memory: 22876K
[ 3.310215] alg: self-tests for CTR-KDF (hmac(sha256)) passed
[ 3.311012] bounce: pool size: 64 pages
[ 3.311361] Block layer SCSI generic (bsg) driver version 0.4 loaded
(major 250)
[ 3.311673] io scheduler mq-deadline registered
[ 3.340434] imx-sdma 20ec000.dma-controller: firmware: failed to load
imx/ sdma/sdma-imx6q.bin (-2)
[ 3.340453] firmware_class: See https://wiki.debian.org/Firmware for
information about missing firmware
[ 3.340529] imx-sdma 20ec000.dma-controller: firmware: failed to load
imx/ sdma/sdma-imx6q.bin (-2)
[ 3.340541] imx-sdma 20ec000.dma-controller: Direct firmware load for
imx/ sdma/sdma-imx6q.bin failed with error -2
[ 3.342750] mxs-dma 110000.dma-apbh: initialized
[ 3.351333] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled
[ 3.354825] Serial: AMBA driver
[ 3.355886] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 28,
base_baud = 5000000) is a IMX
[ 3.383475] printk: console [ttymxc0] enabled
[ 3.384855] 21f0000.serial: ttymxc3 at MMIO 0x21f0000 (irq = 29,
base_baud = 5000000) is a IMX
[ 3.387076] STM32 USART driver initialized
[ 3.390343] mousedev: PS/2 mouse device common for all mice
[ 3.393534] snvs_rtc 20cc000.snvs:snvs-rtc-lp: registered as rtc0
[ 3.393572] snvs_rtc 20cc000.snvs:snvs-rtc-lp: setting system clock to
2023-08-04T06:36:36 UTC (1691130996)
[ 3.398712] ledtrig-cpu: registered to indicate activity on CPUs
[ 3.402641] NET: Registered PF_INET6 protocol family
[ 3.439159] Segment Routing with IPv6
[ 3.439256] In-situ OAM (IOAM) with IPv6
[ 3.439386] mip6: Mobile IPv6
[ 3.439414] NET: Registered PF_PACKET protocol family
[ 3.439633] mpls_gso: MPLS GSO support
[ 3.440171] ThumbEE CPU extension supported.
[ 3.440192] Registering SWP/SWPB emulation handler
[ 3.440823] registered taskstats version 1
[ 3.440874] Loading compiled-in X.509 certificates
6ccece7e4c6c0d1f6149f3dd27dfcc5cbb419ea1'
14011249c2675ea8e5148542202005810584b25f'
[ 4.502987] zswap: loaded using pool lzo/zbud
[ 4.504123] Key type .fscrypt registered
[ 4.504137] Key type fscrypt-provisioning registered
[ 4.539205] Key type encrypted registered
[ 4.539238] AppArmor: AppArmor sha1 policy hashing enabled
[ 4.539299] ima: No TPM chip found, activating TPM-bypass!
[ 4.539344] ima: Allocated hash algorithm: sha256
[ 4.539402] ima: No architecture policies found
[ 4.539531] evm: security.selinux
[ 4.539539] evm: security.SMACK64 (disabled)
[ 4.539547] evm: security.SMACK64EXEC (disabled)
[ 4.539554] evm: security.SMACK64TRANSMUTE (disabled)
[ 4.539560] evm: security.SMACK64MMAP (disabled)
[ 4.539566] evm: security.apparmor
[ 4.539575] evm: security.ima
[ 4.539580] evm: security.capability
[ 4.539588] evm: HMAC attrs: 0x1
[ 5.875246] Freeing unused kernel image (initmem) memory: 2048K
[ 5.880812] Checked W+X mappings: passed, no W+X pages found
[ 5.880841] Run /init as init process
[ 5.880863] /init
[ 5.880881] HOME=/
[ 5.880888] TERM=linux
[ 6.942032] gpio-keys gpio-keys: Unable to get irq number for GPIO 0,
error -6
[ 7.050773] imx-gpc 20dc000.gpc: Failed to create device link (0x180)
with 20c8000.anatop:regulator-vddpu
[ 7.160706] SCSI subsystem initialized
[ 7.194844] libata version 3.00 loaded.
[ 7.226016] pps_core: LinuxPPS API ver. 1 registered
[ 7.226035] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo
[ 7.231464] PTP clock support registered
[ 7.233785] sdhci: Secure Digital Host Controller Interface driver
[ 7.233798] sdhci: Copyright(c) Pierre Ossman
[ 7.246250] sdhci-pltfm: SDHCI platform and OF driver helper
[ 7.257166] ahci-imx 2200000.sata: fsl,transmit-level-mV value 1104,
using 00000044
[ 7.257193] ahci-imx 2200000.sata: fsl,transmit-boost-mdB value 0, using
00000000
[ 7.257207] ahci-imx 2200000.sata: fsl,transmit-atten-16ths value 9,
using 00002000
[ 7.257221] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified,
using 05000000
[ 7.257307] ahci-imx 2200000.sata: supply ahci not found, using dummy
regulator
[ 7.257598] ahci-imx 2200000.sata: supply phy not found, using dummy
regulator
[ 7.257681] ahci-imx 2200000.sata: supply target not found, using dummy
regulator
[ 7.270383] ahci-imx 2200000.sata: SSS flag set, parallel bus scan
disabled [ 7.270426] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1
ports 3 Gbps 0x1 impl platform mode
[ 7.270445] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only
pmp pio slum part ccc apst
[ 7.275787] sdhci-esdhc-imx 2190000.mmc: allocated mmc-pwrseq
[ 7.277295] i2c i2c-1: IMX I2C adapter registered
[ 7.279156] sdhci-esdhc-imx 2194000.mmc: Got CD GPIO
[ 7.280358] rtc-pcf8523 2-0068: failed to set xtal load capacitance: -6
[ 7.281510] i2c i2c-2: IMX I2C adapter registered
[ 7.292001] usbcore: registered new interface driver usbfs
[ 7.292075] usbcore: registered new interface driver hub
[ 7.292155] usbcore: registered new device driver usb
[ 7.292391] scsi host0: ahci-imx
[ 7.293026] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port
0x100 irq 269
[ 7.331670] mmc1: SDHCI controller on 2194000.mmc [2194000.mmc] using
ADMA [ 7.352182] usb_phy_generic usbphynop1: supply vcc not found, using
dummy regulator
[ 7.352409] usb_phy_generic usbphynop1: dummy supplies not allowed for
exclusive requests
[ 7.352628] usb_phy_generic usbphynop2: supply vcc not found, using dummy
regulator
[ 7.352952] usb_phy_generic usbphynop2: dummy supplies not allowed for
exclusive requests
[ 7.364400] mmc1: host does not support reading read-only switch,
assuming write-enable
[ 7.367198] mmc1: new high speed SDHC card at address 0007
[ 7.369010] mmcblk1: mmc1:0007 SD08G 7.42 GiB
[ 7.375838] mmcblk1: p1 p2 p3 p4 < p5 >
[ 7.515172] mmc0: SDHCI controller on 2190000.mmc [2190000.mmc] using
ADMA [ 7.590761] mmc0: new high speed SDIO card at address 0001
[ 7.606510] ata1: SATA link down (SStatus 0 SControl 300)
[ 7.606569] ahci-imx 2200000.sata: no device found, disabling link.
[ 7.606582] ahci-imx 2200000.sata: pass .hotplug=1 to enable hotplug
[ 7.667264] imx_usb 2184000.usb: No over current polarity defined
[ 7.667615] pps pps0: new PPS source ptp0
[ 7.707099] ci_hdrc ci_hdrc.0: EHCI Host Controller
[ 7.707159] ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus
number 1
[ 7.725381] ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00
[ 7.727171] usb usb1: New USB device found, idVendor=1d6b,
idProduct=0002, bcdDevice= 6.01
[ 7.727194] usb usb1: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 7.727209] usb usb1: Product: EHCI Host Controller
[ 7.727218] usb usb1: Manufacturer: Linux 6.1.0-10-armmp ehci_hcd
[ 7.727228] usb usb1: SerialNumber: ci_hdrc.0
[ 7.730507] hub 1-0:1.0: USB hub found
[ 7.730588] hub 1-0:1.0: 1 port detected
[ 7.734745] imx_usb 2184200.usb: No over current polarity defined
[ 7.739373] ci_hdrc ci_hdrc.1: EHCI Host Controller
[ 7.739417] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus
number 2
[ 7.744894] mdio_bus 2188000.ethernet-1: MDIO device at address 4 is
missing.
[ 7.763968] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
[ 7.764349] usb usb2: New USB device found, idVendor=1d6b,
idProduct=0002, bcdDevice= 6.01
[ 7.764369] usb usb2: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 7.764382] usb usb2: Product: EHCI Host Controller
[ 7.764393] usb usb2: Manufacturer: Linux 6.1.0-10-armmp ehci_hcd
[ 7.764404] usb usb2: SerialNumber: ci_hdrc.1
[ 7.766511] hub 2-0:1.0: USB hub found
[ 7.766588] hub 2-0:1.0: 1 port detected
[ 7.771809] fec 2188000.ethernet eth0: registered PHC device 0
[ 7.942031] fec 2188000.ethernet end0: renamed from eth0
[ 8.432643] PM: Image not found (code -22)
[ 8.845852] EXT4-fs (mmcblk1p3): mounted filesystem with ordered data
mode. Quota mode: none.
[ 9.150061] Not activating Mandatory Access Control as /sbin/tomoyo-init
does not exist.
[ 9.966944] systemd[1]: Inserted module 'autofs4'
[ 10.074961] systemd[1]: systemd 252.12-1~deb12u1 running in system mode
(+PAM +AUDIT +SELINUX +APPARMOR +IMA +SMACK +SECCOMP +GCRYPT -GNUTLS
+OPENSSL +ACL +BLKID +CURL +ELFUTILS +FIDO2 +IDN2 -IDN +IPTC +KMOD
+LIBCRYPTSETUP +LIBFDISK +PCRE2 -PWQUALITY +P11KIT +QRENCODE +TPM2 +BZIP2
+LZ4 +XZ +ZLIB +ZSTD -BPF_FRAMEWORK -XKBCOMMON +UTMP +SYSVINIT
default-hierarchy=unified) [ 10.075013] systemd[1]: Detected architecture
arm.
[ 10.094455] systemd[1]: Hostname set to <test-machine>.
[ 11.467237] systemd[1]: Queued start job for default target
graphical.target.
[ 11.495510] systemd[1]: Created slice system-getty.slice - Slice /system/
getty.
[ 11.499086] systemd[1]: Created slice system-modprobe.slice - Slice /
system/modprobe.
[ 11.502204] systemd[1]: Created slice system-serial\x2dgetty.slice -
Slice /system/serial-getty.
[ 11.505452] systemd[1]: Created slice system-systemd\x2dfsck.slice -
Slice /system/systemd-fsck.
[ 11.507610] systemd[1]: Created slice user.slice - User and Session
Slice. [ 11.508355] systemd[1]: Started systemd-ask-password-console.path
- Dispatch Password Requests to Console Directory Watch.
[ 11.508940] systemd[1]: Started systemd-ask-password-wall.path - Forward
Password Requests to Wall Directory Watch.
[ 11.510472] systemd[1]: Set up automount
proc-sys-fs-binfmt_misc.automount - Arbitrary Executable File Formats File
System Automount Point.
[ 11.511085] systemd[1]: Reached target cryptsetup.target - Local
Encrypted Volumes.
[ 11.511469] systemd[1]: Reached target integritysetup.target - Local
Integrity Protected Volumes.
[ 11.512148] systemd[1]: Reached target paths.target - Path Units.
[ 11.512436] systemd[1]: Reached target remote-fs.target - Remote File
Systems.
[ 11.512690] systemd[1]: Reached target slices.target - Slice Units.
[ 11.513239] systemd[1]: Reached target veritysetup.target - Local Verity
Protected Volumes.
[ 11.514529] systemd[1]: Listening on syslog.socket - Syslog Socket.
[ 11.515521] systemd[1]: Listening on systemd-fsckd.socket - fsck to fsckd
communication Socket.
[ 11.516232] systemd[1]: Listening on systemd-initctl.socket - initctl
Compatibility Named Pipe.
[ 11.518059] systemd[1]: Listening on systemd-journald-audit.socket -
Journal Audit Socket.
[ 11.519157] systemd[1]: Listening on systemd-journald-dev-log.socket -
Journal Socket (/dev/log).
[ 11.520473] systemd[1]: Listening on systemd-journald.socket - Journal
Socket.
[ 11.529336] systemd[1]: Listening on systemd-udevd-control.socket - udev
Control Socket.
[ 11.530427] systemd[1]: Listening on systemd-udevd-kernel.socket - udev
Kernel Socket.
[ 11.531665] systemd[1]: dev-hugepages.mount - Huge Pages File System was
skipped because of an unmet condition check
(ConditionPathExists=/sys/kernel/ mm/hugepages).
[ 11.552494] systemd[1]: Mounting dev-mqueue.mount - POSIX Message Queue
File System...
[ 11.560315] systemd[1]: Mounting sys-kernel-debug.mount - Kernel Debug
File System...
[ 11.569396] systemd[1]: Mounting sys-kernel-tracing.mount - Kernel Trace
File System...
[ 11.589071] systemd[1]: Starting kmod-static-nodes.service - Create List
of Static Device Nodes...
Module configfs...
Module dm_mod...
Module drm...
Kernel Module efi_pstore...
Module fuse...
Module loop...
[ 11.702251] systemd[1]: systemd-fsck-root.service - File System Check on
Root Device was skipped because of an unmet condition check
(ConditionPathExists=!/run/initramfs/fsck-root).
[ 11.729860] device-mapper: core: CONFIG_IMA_DISABLE_HTABLE is disabled.
Duplicate IMA measurements will not be recorded in the IMA log.
[ 11.730065] device-mapper: uevent: version 1.0.3
[ 11.753390] systemd[1]: Starting systemd-journald.service - Journal
Service...
[ 11.792040] systemd[1]: Starting systemd-modules-load.service - Load
Kernel Modules...
[ 11.810304] loop: module loaded
[ 11.813799] fuse: init (API version 7.37)
[ 11.821774] systemd[1]: Starting systemd-remount-fs.service - Remount
Root and Kernel File Systems...
[ 11.850473] systemd[1]: Starting systemd-udev-trigger.service - Coldplug
All udev Devices...
[ 11.876647] systemd[1]: Mounted dev-mqueue.mount - POSIX Message Queue
File System.
[ 11.877732] systemd[1]: Mounted sys-kernel-debug.mount - Kernel Debug
File System.
[ 11.878866] systemd[1]: Mounted sys-kernel-tracing.mount - Kernel Trace
File System.
[ 11.881032] systemd[1]: Finished kmod-static-nodes.service - Create List
of Static Device Nodes.
- Load Kernel Module configfs.
Load Kernel Module dm_mod.
Module drm.
successfully.
Kernel Module efi_pstore.
Module fuse.
Module loop.
[ 11.968569] systemd[1]: Mounting sys-fs-fuse-connections.mount - FUSE
Control File System...
[ 11.989102] systemd[1]: Mounting sys-kernel-config.mount - Kernel
Configuration File System...
[ 11.990014] systemd[1]: systemd-repart.service - Repartition Root Disk
was skipped because no trigger condition checks were met.
[ 12.007535] systemd[1]: Finished systemd-modules-load.service - Load
Kernel Modules.
[ 12.023840] systemd[1]: Starting systemd-sysctl.service - Apply Kernel
Variables...
[ 12.036049] EXT4-fs (mmcblk1p3): re-mounted. Quota mode: none.
[ 12.069546] systemd[1]: Finished systemd-remount-fs.service - Remount
Root and Kernel File Systems.
[ 12.071243] systemd[1]: Mounted sys-fs-fuse-connections.mount - FUSE
Control File System.
[ 12.072274] systemd[1]: Mounted sys-kernel-config.mount - Kernel
Configuration File System.
[ 12.073480] systemd[1]: systemd-firstboot.service - First Boot Wizard was
skipped because of an unmet condition check (ConditionFirstBoot=yes). [
12.073937] systemd[1]: systemd-pstore.service - Platform Persistent Storage
Archival was skipped because of an unmet condition check
(ConditionDirectoryNotEmpty=/sys/fs/pstore).
[ 12.105340] systemd[1]: Starting systemd-random-seed.service - Load/Save
Random Seed...
[ 12.115715] systemd[1]: Starting systemd-sysusers.service - Create System
Users...
[ 12.292469] systemd[1]: Finished systemd-sysctl.service - Apply Kernel
Variables.
[ 12.345094] systemd[1]: Finished systemd-sysusers.service - Create System
Users.
[ 12.385089] systemd[1]: Starting systemd-tmpfiles-setup-dev.service -
Create Static Device Nodes in /dev...
[ 12.386139] systemd[1]: Started systemd-journald.service - Journal
Service. [ 12.517675] systemd-journald[197]: Received client request to
flush runtime journal.
[ 14.255890] random: crng init done
[ 16.918706] Registered IR keymap rc-empty
[ 16.920783] rc rc0: gpio_ir_recv as /devices/platform/ir-receiver/rc/rc0
[ 16.921060] rc rc0: lirc_dev: driver gpio_ir_recv registered at minor =
0, raw IR receiver, no transmitter
[ 16.921237] input: gpio_ir_recv as /devices/platform/ir-receiver/rc/rc0/
input4
[ 16.964853] imx-ipuv3 2400000.ipu: IPUv3H probed
[ 16.974913] imx-ipuv3 2800000.ipu: IPUv3H probed
[ 17.011399] mc: Linux media interface: v0.10
[ 17.152579] dwhdmi-imx 120000.hdmi: Detected HDMI TX controller v1.30a
with HDCP (DWC HDMI 3D TX PHY)
[ 17.161854] videodev: Linux video capture interface: v2.00
[ 17.192606] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv])
[ 17.200105] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv])
[ 17.206541] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv])
[ 17.206692] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108
[ 17.213585] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007
[ 17.213689] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215
[ 17.213705] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0
[ 17.214393] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor
0 [ 17.281957] imx_media_common: module is from the staging directory,
the quality is unknown, you have been warned.
[ 17.298944] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops
imx_drm_exit [imxdrm])
[ 17.299141] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops
imx_drm_exit [imxdrm])
[ 17.299304] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops
imx_drm_exit [imxdrm])
[ 17.299443] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops
imx_drm_exit [imxdrm])
[ 17.299529] imx-drm display-subsystem: bound 120000.hdmi (ops
dw_hdmi_imx_ops [dw_hdmi_imx])
[ 17.307930] [drm] Initialized imx-drm 1.0.0 20120507 for
display-subsystem on minor 1
[ 17.308074] imx-drm display-subsystem: [drm] Cannot find any crtc or
sizes [ 17.335371] imx6_media: module is from the staging directory, the
quality is unknown, you have been warned.
[ 17.468441] imx-drm display-subsystem: [drm] Cannot find any crtc or
sizes [ 17.500845] coda 2040000.vpu: firmware: failed to load
vpu_fw_imx6q.bin (-2) [ 17.516104] coda 2040000.vpu: firmware: failed to
load vpu_fw_imx6q.bin (-2) [ 17.523271] coda 2040000.vpu: Direct firmware
load for vpu_fw_imx6q.bin failed with error -2
[ 17.531273] caam 2100000.crypto: Entropy delay = 3200
[ 17.548018] coda 2040000.vpu: firmware: failed to load
vpu/vpu_fw_imx6q.bin (-2)
[ 17.563935] coda 2040000.vpu: firmware: failed to load
vpu/vpu_fw_imx6q.bin (-2)
[ 17.571368] coda 2040000.vpu: Direct firmware load for
vpu/vpu_fw_imx6q.bin failed with error -2
[ 17.571474] coda 2040000.vpu: firmware: failed to load
v4l-coda960-imx6q.bin (-2)
[ 17.582971] coda 2040000.vpu: firmware: failed to load
v4l-coda960-imx6q.bin (-2)
[ 17.590487] coda 2040000.vpu: Direct firmware load for
v4l-coda960-imx6q.bin failed with error -2
[ 17.590504] coda 2040000.vpu: firmware request failed
[ 17.592073] caam 2100000.crypto: Instantiated RNG4 SH0
[ 17.652839] caam 2100000.crypto: Instantiated RNG4 SH1
[ 17.708454] imx_thermal 20c8000.anatop:tempmon: Extended Commercial CPU
temperature grade - max:105C critical:100C passive:95C
[ 17.993983] imx-spdif sound-spdif: ASoC: driver name too long 'Integrated
SPDIF' -> 'Integrated_SPDI'
[ 18.165195] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4)
[ 18.165222] caam 2100000.crypto: job rings = 2, qi = 0
[ 18.174579] cfg80211: Loading compiled-in X.509 certificates for
regulatory database
577e021cb980e0e820821ba7b54b4961b8b4fadf'
3abbc6ec146e09d1b6016ab9d6cf71dd233f0328'
[ 18.212839] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 18.214231] imx6_media_csi: module is from the staging directory, the
quality is unknown, you have been warned.
[ 18.215153] imx6_media_csi: module is from the staging directory, the
quality is unknown, you have been warned.
[ 18.216199] platform regulatory.0: firmware: direct-loading firmware
regulatory.db
[ 18.216795] imx6_media_csi: module is from the staging directory, the
quality is unknown, you have been warned.
[ 18.217346] platform regulatory.0: firmware: direct-loading firmware
regulatory.db.p7s
[ 18.224411] imx6_media_csi: module is from the staging directory, the
quality is unknown, you have been warned.
[ 18.308262] imx-ipuv3-csi imx-ipuv3-csi.0: Registered ipu1_csi0 capture
as /dev/video0
[ 18.309066] imx-ipuv3 2400000.ipu: Registered ipu1_ic_prpenc capture as /
dev/video1
[ 18.309669] imx-ipuv3 2400000.ipu: Registered ipu1_ic_prpvf capture as /
dev/video2
[ 18.309747] video-mux 20e0000.iomuxc-gpr:ipu1_csi0_mux: Consider updating
driver video-mux to match on endpoints
[ 18.311385] imx-ipuv3-csi imx-ipuv3-csi.1: Registered ipu1_csi1 capture
as /dev/video3
[ 18.317301] imx-ipuv3-csi imx-ipuv3-csi.4: Registered ipu2_csi0 capture
as /dev/video4
[ 18.317759] imx-ipuv3 2800000.ipu: Registered ipu2_ic_prpenc capture as /
dev/video5
[ 18.318093] imx-ipuv3 2800000.ipu: Registered ipu2_ic_prpvf capture as /
dev/video6
[ 18.319831] imx-ipuv3-csi imx-ipuv3-csi.5: Registered ipu2_csi1 capture
as /dev/video7
[ 18.319936] video-mux 20e0000.iomuxc-gpr:ipu2_csi1_mux: Consider updating
driver video-mux to match on endpoints
[ 18.321283] Registered IR keymap rc-cec
[ 18.321442] rc rc1: dw_hdmi as /devices/platform/soc/120000.hdmi/rc/rc1
[ 18.321649] input: dw_hdmi as /devices/platform/soc/120000.hdmi/rc/rc1/
input5
[ 18.332205] brcmfmac: brcmf_fw_alloc_request: using
brcm/brcmfmac4330-sdio for chip BCM4330/4
[ 18.333435] usbcore: registered new interface driver brcmfmac
[ 18.349057] brcmfmac mmc0:0001:1: firmware: failed to load brcm/
brcmfmac4330-sdio.solidrun,cubox-i-q.bin (-2)
[ 18.364003] brcmfmac mmc0:0001:1: firmware: failed to load brcm/
brcmfmac4330-sdio.solidrun,cubox-i-q.bin (-2)
[ 18.368259] Adding 994300k swap on /dev/mmcblk1p5. Priority:-2 extents:1
across:994300k SSFS
[ 18.374043] brcmfmac mmc0:0001:1: Direct firmware load for brcm/
brcmfmac4330-sdio.solidrun,cubox-i-q.bin failed with error -2
[ 18.397990] brcmfmac mmc0:0001:1: firmware: direct-loading firmware brcm/
brcmfmac4330-sdio.bin
[ 18.398133] brcmfmac mmc0:0001:1: firmware: failed to load brcm/
brcmfmac4330-sdio.solidrun,cubox-i-q.txt (-2)
[ 18.410094] brcmfmac mmc0:0001:1: firmware: failed to load brcm/
brcmfmac4330-sdio.solidrun,cubox-i-q.txt (-2)
[ 18.424678] brcmfmac mmc0:0001:1: firmware: failed to load brcm/
brcmfmac4330-sdio.txt (-2)
[ 18.433481] brcmfmac mmc0:0001:1: firmware: failed to load brcm/
brcmfmac4330-sdio.txt (-2)
[ 18.441836] brcmfmac mmc0:0001:1: Direct firmware load for brcm/
brcmfmac4330-sdio.txt failed with error -2
[ 18.460274] imx-media: Registered ipu_ic_pp csc/scaler as /dev/video8
[ 18.952893] alg: No test for authenc(hmac(sha224),ecb(cipher_null))
(authenc-hmac-sha224-ecb-cipher_null-caam)
[ 18.953078] alg: No test for authenc(hmac(sha256),ecb(cipher_null))
(authenc-hmac-sha256-ecb-cipher_null-caam)
[ 18.953259] alg: No test for authenc(hmac(md5),cbc(aes))
(authenc-hmac-md5- cbc-aes-caam)
[ 18.953425] alg: No test for echainiv(authenc(hmac(md5),cbc(aes)))
(echainiv-authenc-hmac-md5-cbc-aes-caam)
[ 18.966350] alg: No test for echainiv(authenc(hmac(sha1),cbc(aes)))
(echainiv-authenc-hmac-sha1-cbc-aes-caam)
[ 18.966561] alg: No test for authenc(hmac(sha224),cbc(aes))
(authenc-hmac- sha224-cbc-aes-caam)
[ 18.966775] alg: No test for echainiv(authenc(hmac(sha224),cbc(aes)))
(echainiv-authenc-hmac-sha224-cbc-aes-caam)
[ 18.996074] EXT4-fs (mmcblk1p2): mounting ext2 file system using the ext4
subsystem
[ 18.996909] alg: No test for echainiv(authenc(hmac(sha256),cbc(aes)))
(echainiv-authenc-hmac-sha256-cbc-aes-caam)
[ 18.997909] alg: No test for authenc(hmac(md5),cbc(des3_ede)) (authenc-
hmac-md5-cbc-des3_ede-caam)
[ 19.002520] alg: No test for echainiv(authenc(hmac(md5),cbc(des3_ede)))
(echainiv-authenc-hmac-md5-cbc-des3_ede-caam)
[ 19.011582] alg: No test for echainiv(authenc(hmac(sha1),cbc(des3_ede)))
(echainiv-authenc-hmac-sha1-cbc-des3_ede-caam)
[ 19.014611] alg: No test for
echainiv(authenc(hmac(sha224),cbc(des3_ede)))
(echainiv-authenc-hmac-sha224-cbc-des3_ede-caam)
[ 19.017669] alg: No test for
echainiv(authenc(hmac(sha256),cbc(des3_ede)))
(echainiv-authenc-hmac-sha256-cbc-des3_ede-caam)
[ 19.017886] alg: No test for authenc(hmac(md5),cbc(des))
(authenc-hmac-md5- cbc-des-caam)
[ 19.018093] alg: No test for echainiv(authenc(hmac(md5),cbc(des)))
(echainiv-authenc-hmac-md5-cbc-des-caam)
[ 19.021435] alg: No test for echainiv(authenc(hmac(sha1),cbc(des)))
(echainiv-authenc-hmac-sha1-cbc-des-caam)
[ 19.024530] alg: No test for echainiv(authenc(hmac(sha224),cbc(des)))
(echainiv-authenc-hmac-sha224-cbc-des-caam)
[ 19.027199] alg: No test for echainiv(authenc(hmac(sha256),cbc(des)))
(echainiv-authenc-hmac-sha256-cbc-des-caam)
[ 19.027439] alg: No test for authenc(hmac(md5),rfc3686(ctr(aes)))
(authenc- hmac-md5-rfc3686-ctr-aes-caam)
[ 19.027639] alg: No test for seqiv(authenc(hmac(md5),rfc3686(ctr(aes))))
(seqiv-authenc-hmac-md5-rfc3686-ctr-aes-caam)
[ 19.029561] alg: No test for seqiv(authenc(hmac(sha1),rfc3686(ctr(aes))))
(seqiv-authenc-hmac-sha1-rfc3686-ctr-aes-caam)
[ 19.029810] alg: No test for authenc(hmac(sha224),rfc3686(ctr(aes)))
(authenc-hmac-sha224-rfc3686-ctr-aes-caam)
[ 19.030043] alg: No test for
seqiv(authenc(hmac(sha224),rfc3686(ctr(aes))))
(seqiv-authenc-hmac-sha224-rfc3686-ctr-aes-caam)
[ 19.030429] alg: No test for
seqiv(authenc(hmac(sha256),rfc3686(ctr(aes))))
(seqiv-authenc-hmac-sha256-rfc3686-ctr-aes-caam)
[ 19.030471] caam algorithms registered in /proc/crypto
[ 19.193425] EXT4-fs (mmcblk1p2): mounted filesystem without journal.
Quota mode: none.
[ 19.193491] ext2 filesystem being mounted at /boot supports timestamps
until 2038 (0x7fffffff)
clkctl 0x50
[ 19.548530] caam 2100000.crypto: registering rng-caam
[ 19.549448] alg: No test for stdrng (prng-caam)
[ 19.549533] caam 2100000.crypto: rng crypto API alg registered prng-caam
[ 20.374413] audit: type=1400 audit(1691131013.476:2): apparmor="STATUS"
operation="profile_load" profile="unconfined" name="lsb_release" pid=379
comm="apparmor_parser"
[ 20.399360] audit: type=1400 audit(1691131013.500:3): apparmor="STATUS"
operation="profile_load" profile="unconfined" name="nvidia_modprobe" pid=380
comm="apparmor_parser"
[ 20.408591] audit: type=1400 audit(1691131013.512:4): apparmor="STATUS"
operation="profile_load" profile="unconfined" name="nvidia_modprobe//kmod"
pid=380 comm="apparmor_parser"
[ 21.161295] audit: type=1400 audit(1691131014.264:5): apparmor="STATUS"
operation="profile_load" profile="unconfined" name="/usr/bin/man" pid=383
comm="apparmor_parser"
[ 21.166429] audit: type=1400 audit(1691131014.268:6): apparmor="STATUS"
operation="profile_load" profile="unconfined" name="man_filter" pid=383
comm="apparmor_parser"
[ 21.173977] audit: type=1400 audit(1691131014.276:7): apparmor="STATUS"
operation="profile_load" profile="unconfined" name="man_groff" pid=383
comm="apparmor_parser"
[ 21.949302] audit: type=1400 audit(1691131015.052:8): apparmor="STATUS"
operation="profile_load" profile="unconfined"
name="/usr/lib/NetworkManager/nm- dhcp-client.action" pid=382
comm="apparmor_parser"
[ 21.958540] audit: type=1400 audit(1691131015.060:9): apparmor="STATUS"
operation="profile_load" profile="unconfined"
name="/usr/lib/NetworkManager/nm- dhcp-helper" pid=382
comm="apparmor_parser"
[ 21.966793] audit: type=1400 audit(1691131015.068:10): apparmor="STATUS"
operation="profile_load" profile="unconfined"
name="/usr/lib/connman/scripts/ dhclient-script" pid=382
comm="apparmor_parser"
[ 21.984009] audit: type=1400 audit(1691131015.084:11): apparmor="STATUS"
operation="profile_load" profile="unconfined" name="/{,usr/}sbin/dhclient"
pid=382 comm="apparmor_parser"
Many thanks
Rainer

--
Rainer Dorsch
Beatus-Widmann-Str. 5
72138 Kirchentellinsfurt
07157/734133

Fan Naibed

2023-09-28 03:30:01 UTC

Post by Rainer Dorsch
# The primary network interface
allow-hotplug eth0
iface eth0 inet dhcp
# This is an autoconfigured IPv6 interface
iface eth0 inet6 auto
I hope that helps somebody to debug his network issues.
Rainer
I hope that helps somebody to debug his network issues.

Rainer, Thank you very much for reporting your issue and workaround fix.

A couple days ago I had the same network issue after upgrading Debian
testing on Pine64 H64B (previous discussion:
https://lists.debian.org/debian-arm/2021/09/msg00001.html ). This is an
arm64 system. I was eventually able to get it running Debian testing,
but it had later stopped responding to remote logins after an upgrade
some weeks or months ago. So a couple days ago, I finally connected it
to a monitor and saw it was dropping to "emergency mode" when rebooted.
Oddly, logging in as root, doing essentially nothing except looking at
logs, df -h, etc, then continuing, it ran OK long enough to do an
upgrade that ran into the renamed ethernet interface issue. The good
news is: After renaming from eth0 to end0 in interfaces, ethernet worked
again. The bad news is: After upgrading another time, the system drops
to "emergency mode" after every reboot. I haven't had time to find
anything obvious in logs, or to add a comment to your bug report.

I have several other headless SBCs, mostly raspberry pis from 1 through
4. After getting them all running Debian testing, they have all slowly
stopped responding over the network after upgrades. One of them, also
just checked with a display, acts like it has a bad sd card, but I
expect others may be having this renamed interface issue, because they
were all originally set up with the same interfaces file using "eth0",
IIRC.

I know it's called "testing" for a reason, but for the most part my
experiences with testing on x86_64 desktop systems has been much more
stable, probably because network "just worked" without hand file
editing. :)

I'll be looking for better ways of setting up headless SBCs if anyone
has good pointers. Thanks!

Rainer Dorsch

2023-09-29 20:10:01 UTC