Forgot to write that I tried this line manually:
Marvell>> setenv bootcmd_usb 'usb start; ext4load usb 0:1 0x00800000
/uImage; ext4load usb 0:1 0x01100000 /uInitrd'
Marvell>> print
baudrate=115200
bootargs=console=ttyS0,115200
bootargs_console=console=ttyS0,115200
bootcmd=setenv bootargs $(bootargs_console); run bootcmd_usb; bootm
0x00800000 0x01100000
bootcmd_usb=usb start; ext4load usb 0:1 0x00800000 /uImage; ext4load usb
0:1 0x01100000 /uInitrd
bootdelay=3
ethact=egiga0
ethaddr=02:50:43:e7:5c:e1
ipaddr=192.168.0.10
serverip=192.168.0.12
stderr=serial
stdin=serial
stdout=serial
x_bootargs=console=ttyS0,115200
mtdparts=orion_nand:512k(uboot),***@1m(kernel),***@5m(rootfs) rw
x_bootargs_root=ubi.mtd=2 root=ubi0:rootfs rootfstype=ubifs
x_bootcmd_kernel=nand read 0x6400000 0x100000 0x400000
x_bootcmd_sata=ide reset;
x_bootcmd_usb=usb start;
Environment size: 706/131068 bytes
Marvell>> run bootcmd
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Unknown command 'ext4load' - try 'help'
Unknown command 'ext4load' - try 'help'
## Booting kernel from Legacy Image at 00800000 ...
Image Name: kernel 4.9.0-18-marvell
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2080634 Bytes = 2 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... Bad Data CRC
ERROR: can't get kernel image!
Marvell>>
Post by GillesI used another USB stick, with the root+boot formated in ext4, the
=========
U-Boot 2011.12 (Mar 11 2012 - 18:59:46)
Marvell-Sheevaplug - eSATA - SD/MMC
SoC: Kirkwood 88F6281_A0
DRAM: 512 MiB
WARNING: Caches not enabled
NAND: 512 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
88E1116 Initialized on egiga0
Hit any key to stop autoboot: 0
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Loading file "/uImage" from usb device 0:1 (usbda1)
Failed to mount ext2 filesystem...
** Bad ext2 partition or disk - usb 0:1 **
Loading file "/uInitrd" from usb device 0:1 (usbda1)
Failed to mount ext2 filesystem...
** Bad ext2 partition or disk - usb 0:1 **
## Booting kernel from Legacy Image at 00800000 ...
Image Name: kernel 4.9.0-18-marvell
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2080634 Bytes = 2 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... Bad Data CRC
ERROR: can't get kernel image!
Marvell>>
=========
setenv bootargs_console console=ttyS0,115200
setenv bootcmd_usb 'usb start; ext2load usb 0:1 0x00800000 /uImage;
ext2load usb 0:1 0x01100000 /uInitrd'
setenv bootcmd 'setenv bootargs $(bootargs_console); run bootcmd_usb;
bootm 0x00800000 0x01100000'
=> Does Uboot support ext4, or just ext2? Or is the 2011.12 release
too old, and I should either upgrade or go back to ext2 instead?
Post by Philip HandsPost by GillesPost by GillesIt ends with a single error : "partman: mkswap: can't open
https://pastebin.com/raw/h0beZWnP
It looks like /dev/sd5 doesn't actually exist. This is probably
because the USB stick has an MBR partition table which by default
only provides partitions 1-4. You may need to pre-partition it
with a GUID partition table.
Rick
Good call. After using Windows' diskpart*, I removed the MBR and
https://postimg.cc/ns5XMQL7
https://pastebin.com/raw/htYCmhS3
The ``bad block bitmap checksum'' relating to /dev/sda2, followed by
``Remounting filesystem read-only'' seems to be the source of your
problem.
After that point nothing's going to work because your new root
filesystem (/target/) is faulty, and is now read-only, so there's no way
to create the /target/boot directory, so the mount of the boot partition
fails.
My guess would be an underlying hardware fault on whatever /dev/sda2 is.
http://oss.digirati.com.br/f3/ (packaged for Debian as ``f3'')
Cheers, Phil.